adjustments to pins

Author: rhooper

ports/espressif/boards/tulip_cc_r11/mpconfigboard.h

@@ -20,7 +20,7 @@
 //#define CONFIG_I2S_LRCLK 2
 //#define CONFIG_I2S_BCLK 8
 
-#define TULIP_DISPLAY_FREQUENCY 10000000
+#define TULIP_DISPLAY_FREQUENCY 16000000
 #define TULIP_DISPLAY_WIDTH     1024
 #define TULIP_DISPLAY_HEIGHT    600
 

ports/espressif/boards/tulip_cc_r11/mpconfigboard.mk

@@ -20,4 +20,4 @@ CIRCUITPY_ESPCAMERA = 0
 CIRCUITPY_DOTCLOCKFRAMEBUFFER = 1
 CIRCUITPY_TINYUSB = 1
 CIRCUITPY_TOUCHIO_USE_NATIVE = 1
-CIRCUITPY_USB_DEVICE = 1
+CIRCUITPY_USB_DEVICE = 1

ports/espressif/boards/tulip_cc_r11/pins.c

@@ -55,7 +55,7 @@
      1 D+  ->
      2 D-  ->
      3 GND
-     4 DTR -> RESET
+     4 DTR -> RESET IO0
      5 CTS
      6 RTS -> IO0
      7 VCC VBUS
@@ -220,6 +220,8 @@ MP_DEFINE_CONST_DICT(timings1024_dict, timings1024_table);
 static const mp_rom_map_elem_t board_module_globals_table[] = {
         CIRCUITPYTHON_BOARD_DICT_STANDARD_ITEMS
 
+        { MP_ROM_QSTR(MP_QSTR_BAT), MP_ROM_PTR(&pin_GPIO3) },
+
         { MP_ROM_QSTR(MP_QSTR_TFT_PINS), MP_ROM_PTR(&tft_pins_dict) },
         { MP_ROM_QSTR(MP_QSTR_TFT_TIMINGS), MP_ROM_PTR(&timings1024_dict) },
         { MP_ROM_QSTR(MP_QSTR_TFT_BACKLIGHT), MP_ROM_PTR(&pin_GPIO47) },
@@ -230,22 +232,14 @@ static const mp_rom_map_elem_t board_module_globals_table[] = {
         { MP_ROM_QSTR(MP_QSTR_I2S_WORD_SELECT), MP_ROM_PTR(&pin_GPIO2) },
         { MP_ROM_QSTR(MP_QSTR_I2S_DATA), MP_ROM_PTR(&pin_GPIO5) },
 
-        // { MP_ROM_QSTR(MP_QSTR_TX), MP_ROM_PTR(&pin_GPIO43) },
-        // { MP_ROM_QSTR(MP_QSTR_RX), MP_ROM_PTR(&pin_GPIO44) },
-
-        // { MP_ROM_QSTR(MP_QSTR_SCL), MP_ROM_PTR(&pin_GPIO18) },
-        // { MP_ROM_QSTR(MP_QSTR_SDA), MP_ROM_PTR(&pin_GPIO17) },
-
-        // USB = D- 19, D+ 20
-
         { MP_ROM_QSTR(MP_QSTR_DISPLAY), MP_ROM_PTR(&displays[0].display) },
 
         { MP_ROM_QSTR(MP_QSTR_MIDI_IN),  MP_ROM_PTR(&pin_GPIO11) },
         { MP_ROM_QSTR(MP_QSTR_MIDI_OUT), MP_ROM_PTR(&pin_GPIO12) },
 
         // boot mode button can be used in SW as well
-        // { MP_ROM_QSTR(MP_QSTR_BOOT0), MP_ROM_PTR(&pin_GPIO0) },
-        // { MP_ROM_QSTR(MP_QSTR_BUTTON), MP_ROM_PTR(&pin_GPIO1) },
+        { MP_ROM_QSTR(MP_QSTR_BOOT0), MP_ROM_PTR(&pin_GPIO0) },
+        { MP_ROM_QSTR(MP_QSTR_BUTTON), MP_ROM_PTR(&pin_GPIO1) },
 
         { MP_ROM_QSTR(MP_QSTR_I2C), MP_ROM_PTR(&board_i2c_obj) },
         { MP_ROM_QSTR(MP_QSTR_UART), MP_ROM_PTR(&board_uart_obj) },

ports/espressif/common-hal/dotclockframebuffer/DotClockFramebuffer.c

@@ -136,26 +136,8 @@ void common_hal_dotclockframebuffer_framebuffer_construct(dotclockframebuffer_fr
 
     int gpio_num = 0;
     allocate_gpio_range(blue, num_blue, expected_blue, cfg, &gpio_num, MP_QSTR_blue);
-    // cfg->data_gpio_nums[0] = valid_pin(blue[0], MP_QSTR_blue);
-    // cfg->data_gpio_nums[1] = valid_pin(blue[1], MP_QSTR_blue);
-    // cfg->data_gpio_nums[2] = valid_pin(blue[2], MP_QSTR_blue);
-    // cfg->data_gpio_nums[3] = valid_pin(blue[3], MP_QSTR_blue);
-    // cfg->data_gpio_nums[4] = valid_pin(blue[4], MP_QSTR_blue);
-
     allocate_gpio_range(green, num_green, expected_green, cfg, &gpio_num, MP_QSTR_green);
-    // cfg->data_gpio_nums[5] = valid_pin(green[0], MP_QSTR_green);
-    // cfg->data_gpio_nums[6] = valid_pin(green[1], MP_QSTR_green);
-    // cfg->data_gpio_nums[7] = valid_pin(green[2], MP_QSTR_green);
-    // cfg->data_gpio_nums[8] = valid_pin(green[3], MP_QSTR_green);
-    // cfg->data_gpio_nums[9] = valid_pin(green[4], MP_QSTR_green);
-    // cfg->data_gpio_nums[10] = valid_pin(green[5], MP_QSTR_green);
-
     allocate_gpio_range(red, num_red, expected_red, cfg, &gpio_num, MP_QSTR_red);
-    // cfg->data_gpio_nums[11] = valid_pin(red[0], MP_QSTR_red);
-    // cfg->data_gpio_nums[12] = valid_pin(red[1], MP_QSTR_red);
-    // cfg->data_gpio_nums[13] = valid_pin(red[2], MP_QSTR_red);
-    // cfg->data_gpio_nums[14] = valid_pin(red[3], MP_QSTR_red);
-    // cfg->data_gpio_nums[15] = valid_pin(red[4], MP_QSTR_red);
 
     cfg->disp_gpio_num = GPIO_NUM_NC;