diff --git a/ports/espressif/boards/heltec_vision_master_t190/board.cmake b/ports/espressif/boards/heltec_vision_master_t190/board.cmake
new file mode 100644
index 00000000..c1426c95
--- /dev/null
+++ b/ports/espressif/boards/heltec_vision_master_t190/board.cmake
@@ -0,0 +1,2 @@
+# Apply board specific content here
+set(IDF_TARGET "esp32s3")
diff --git a/ports/espressif/boards/heltec_vision_master_t190/board.h b/ports/espressif/boards/heltec_vision_master_t190/board.h
new file mode 100644
index 00000000..5af20584
--- /dev/null
+++ b/ports/espressif/boards/heltec_vision_master_t190/board.h
@@ -0,0 +1,93 @@
+/*
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2020 Ha Thach (tinyusb.org) for Adafruit Industries
+ * Copyright (c) 2023 Linar Yusupov
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ */
+
+#pragma once
+
+//--------------------------------------------------------------------+
+// Button
+//--------------------------------------------------------------------+
+
+// Enter UF2 mode if GPIO is pressed while 2nd stage bootloader indicator
+// is on e.g RGB = Purple. If it is GPIO0, user should not hold this while
+// reset since that will instead run the 1st stage ROM bootloader
+#define PIN_BUTTON_UF2    0
+
+// Initial delay in milliseconds to detect user interaction to enter UF2
+#define UF2_DETECTION_DELAY_MS  1000
+
+//--------------------------------------------------------------------+
+// LED
+//--------------------------------------------------------------------+
+
+// LED for indicator and writing flash
+//#define LED_PIN           18
+//#define LED_STATE_ON      1
+
+//--------------------------------------------------------------------+
+// TFT
+//--------------------------------------------------------------------+
+
+#define CONFIG_LCD_TYPE_ST7789V
+
+#define DISPLAY_PIN_MISO      -1 // required if use CONFIG_LCD_TYPE_AUTO
+#define DISPLAY_PIN_MOSI      48
+#define DISPLAY_PIN_SCK       38
+
+#define DISPLAY_PIN_CS        39
+#define DISPLAY_PIN_DC        47
+#define DISPLAY_PIN_RST       40
+
+#define DISPLAY_PIN_BL        7
+#define DISPLAY_BL_ON         0  // GPIO state to enable back light
+
+#define DISPLAY_PIN_POWER     17
+#define DISPLAY_POWER_ON       1  // GPIO state to enable TFT
+
+#define DISPLAY_WIDTH         320
+#define DISPLAY_HEIGHT        170
+
+#define DISPLAY_COL_OFFSET    35
+#define DISPLAY_ROW_OFFSET    0
+
+// Memory Data Access Control & // Vertical Scroll Start Address
+// Rotate display by changing MY to MX below
+#define DISPLAY_MADCTL        TFT_MADCTL_MY
+#define DISPLAY_VSCSAD        0
+
+#define DISPLAY_TITLE         "Heltec T190"
+
+//--------------------------------------------------------------------+
+// USB UF2
+//--------------------------------------------------------------------+
+
+#define USB_VID           0x303A            // Espressif VID
+#define USB_PID           0x1001            // Espressif assigned PID
+#define USB_MANUFACTURER  "Heltec"
+#define USB_PRODUCT       "Vision Master T190"
+
+#define UF2_PRODUCT_NAME  USB_MANUFACTURER " " USB_PRODUCT
+#define UF2_BOARD_ID      "ESP32S3-HT-VMT190-v1.0"
+#define UF2_VOLUME_LABEL  "HTBOOT"
+#define UF2_INDEX_URL     "https://heltec.org/project/vision-master-t190"
diff --git a/ports/espressif/boards/heltec_vision_master_t190/sdkconfig b/ports/espressif/boards/heltec_vision_master_t190/sdkconfig
new file mode 100644
index 00000000..329b9a9f
--- /dev/null
+++ b/ports/espressif/boards/heltec_vision_master_t190/sdkconfig
@@ -0,0 +1,7 @@
+# Board Specific Config
+
+# Partition Table
+CONFIG_PARTITION_TABLE_CUSTOM_FILENAME="partitions-8MB.csv"
+
+# Serial flasher config
+CONFIG_ESPTOOLPY_FLASHSIZE_8MB=y